How To Refill A Scripto Lighter

Download Commodity

Download Article

If yous have a standard disposable, long-stemmed, butane, or windproof Aught lighter, you lot'll somewhen need to refill it. Refilling your lighters is piece of cake and simply takes a few minutes. Simply put the right type of fluid into your lighter when you notice your flame getting low, or when your lighter tin't produce a flame at all. Always do circumspection when refilling a lighter.

1. 1

   Open the refill valve. Turn your lighter upside down. At that place volition be a small hole in the lesser with a slit leading to a modest hole. Insert a push pin into the hole, flip the lighter so the pin is resting against your work surface, and press down on the lighter firmly.^[1]

   • You should feel and hear a modest "pop" as the pin pushes a metallic beebee out of place. This beebee seals the release valve and must be pushed out of the way.
   • To verify the beebee seal has been removed, with the push button pin nonetheless inserted, shake the lighter. You should be able to hear the beebee rattle around.^[2]

2. two

   Purge remaining air in the lighter. This should simply be washed with empty lighters. Point the lighter away from your face and remove the push pin. Yous should hear a puff of air when the pin pulls free.^[three]

   • Attempting to purge a lighter that has fuel remaining within will cause fuel to be sprayed out of the refill valve.
   • To prevent fuel from getting on your piece of work surface, lay down a encompass, like newspaper or a drop material.
   • Wipe down any areas exposed to fuel with a water dampened rag. Also, your easily may have gotten fuel on them. Launder them with soapy h2o.

3. 3

   Create a seal on your butane applicator with rubber grommets. It isn't likely that your butane applicator volition fit perfectly into the lighters refill valve. This can cause gas to leak. Slip three rubber grommets that fit snugly onto the applicator.

   • The rubber of the last grommet should extend merely slightly beyond the tip of the butane spray applicator.
   • Circular rubber grommets can be purchased at your local hardware shop in variety packs in the hardware section.^[four]

4. 4

   Fill up the lighter with butane. Turn the lighter upside down so its lesser faces upwards and its top rests on your work surface. Insert the grommet covered tip of the applicator into the refill valve. Press down on the bottle to undo the refill bottle's release valve.^[5]

   • Considering of the seal formed past the rubber grommets, yous shouldn't hear any dissonance every bit the lighter refills.
   • The lighter should refill completely in near five seconds. When finished, release pressure on the refill bottle but proceed the applicator inserted in the refill valve.^{[half dozen]}

5. 5

   Seal the refill valve. Remove the applicator from the refill valve and quickly seal the valve with your pollex. Hold the valve tightly with your thumb and pick up the push pin with your gratis paw. Quick equally you can, remove your thumb and plug the pigsty with the push pin.

   • You may hear some hissing when your thumb is plugging the refill valve. Hold your thumb firmly to reduce the escape of fuel.
   • This part of refilling a dispensable lighter tin be difficult at outset. Move rapidly to prevent freshly replenished fuel from escaping.^[7]

6. 6

   Remove the end of the push button pivot when necessary. If yous've used a push pivot with a contoured plastic end, this may get defenseless on something and pull the pin out. Cut the contoured plastic at its base with clippers and file downwardly whatever jagged edges with a metal file.^[eight]

1. 1

   Remove the case spiral. There should exist a single spiral property the case of the lighter together at the opposite end from the stem. Unfasten this with a screwdriver, and so turn the case over and tap it confronting your work surface to remove the screw from its hole.^[9]

   • The screws on these types of lighters tend to be very minor, so a regular-sized screwdriver may be too big. Try a mini screwdriver instead.
   • If you tin can't get whatever mini screwdrivers, choice upward a repair kit for glasses. They usually contain a mini screw driver that may piece of work.

2. 2

   Loosen the outer seam of the case with a screwdriver. The outer seam of the lighter will exist held together past a low-cal mucilage and some plastic pins. Run a normal sized flat head screwdriver along the outer seams to loosen the gum.

   • If you can't go a flat head screwdriver, attempt a butter pocketknife instead. Yous need something thin that you can wedge into the seam and pry information technology apart.

3. 3

   Pry open the case. Later the seams accept been loosened, piece of work the tip of your flat head into the seam and gently pry open the stalk-opposite end. When roughly one-half of the example separates, remove the screwdriver.^[10]

4. iv

   Remove the lighter insert. Pull apart the stem-opposite side of the case open with your fingers. Don't pull also hard; the case should only pry apart halfway. At this indicate, you should be able to use your fingers to pull out the fuel reservoir.

   • The fuel reservoir looks very similar to a standard disposable lighter. Place the reservoir and a fresh disposable lighter side by side in forepart of you.
   • The empty long-stemmed lighter tin be set off to the side. This function won't exist needed until yous put the lighter back together.

5. 5

   Disassemble the new disposable lighter. Pry the vented front metal ring (the wind guard) from the lighter with your fingers. Pull out the flint wheel, the attached flint, and flintstone spring. So pull the insert beneath (which includes the push button), its jump, and the nozzle jet free.

   • Subsequently these parts have been removed, proceed the disassembled lighter positioned upright to prevent it from spilling fuel.^[11]

6. 6

   Supervene upon the onetime lighter'south jet with the one from the reservoir. The top of the reservoir should take a similar button-insert every bit the new lighter. Remove this, its spring, and the nozzle jet from the reservoir. Replace the reservoir jet, spring, and insert on the new lighter.

   • The jet and the spring should fall into place easily. Press the push button-insert into place with moderate force. Yous should feel information technology snap into place.

7. vii

   Reinsert the replacement reservoir. Pry open the case halfway one more time. Insert the replacement reservoir into the torso of the lighter so the reservoir button and the trigger of the lighter marshal. Test the lighter. If information technology lights, refasten the case screw and y'all're done.

   • If the lighter does not ignite, it'southward likely the reservoir push-insert, bound, and/or jet were not correctly installed.
   • The reservoir should slot into identify in a small, internal cavity inside the handle of the long-stemmed lighter.^[12]

1. ane

   Buy butane to refill your lighter. You tin can notice refill cans almost anywhere you lot can buy cigarettes or cigars, similar a tobacco store. Look for bottles that come with metal tips instead of plastic ones. Metal tips are better for inserting the butane into the lighter.

   • Verify the butane works with your lighter by reading its label instructions. Always follow the safety directions on the canister to achieve the best results.
   • Select a loftier-quality butane specifically intended for butane lighters. Low-quality fuel may non lite equally well.

2. 2

   Select a flat, sturdy surface to piece of work on. You'll also desire this to be in a place that is well ventilated. Yous'll be dealing with combustible gas while refilling. Expert ventilation will prevent the buildup of harmful fumes.

   • Your kitchen or an outside area are good places to refill your butane lighter because both are open spaces.
   • Open a window or turn on a vent in the room if it is available. If airflow is still poor fifty-fifty with a window open, utilize a stationary fan to improve circulation.
   • Remaining fluid or gas may spray onto your work surface while refilling. Protect your piece of work surface with a layer of newspaper or a driblet cloth.^[thirteen]

3. three

   Purge your lighter. Release the air and remaining fuel within the lighter. While belongings the valve so it's pointed away from your face, push down on the refill lever with a screwdriver.^[14] The air will exist fully released when you no longer hear a hissing audio.^[fifteen]

   • The refill lever is also sometimes known every bit the nipple. It is located on the bottom of most butane lighters and usually looks like a small hole with a tiny, circular valve within.
   • If you don't have a screwdriver, use a pen, paperclip, or similar tool to push down the valve and release remaining air in the lighter.
   • If lighter fluid sprays onto your hands or tools, rinse these thoroughly in soap and water. If you forget to do and then, the fuel may ignite and burn you when y'all test the lighter.

4. four

   Fix the flame meridian adjuster on the lighter to the everyman level. The flame summit adjuster is usually on the bottom of the lighter and looks like a screw with a flat head screwdriver slot. Use a pocket-size flat head screwdriver and turn the screw clockwise to lower the flame.

   • By turning the adjuster to its lowest setting, fifty-fifty if you lot accidentally ignite the lighter, the flame will be modest and unlikely to do damage or damage.
   • Some lighters may bespeak the minimum setting management with a minus sign ( - ). Turn the adjuster spiral towards the minus sign to lower the flame.^[16]

5. 5

   Shake the tin of refill fluid. If y'all have an older can especially, give it a few shakes up-and-downwards. Over time, the fluid can sink to the bottom and non spray effectively. By shaking the can, you lot'll prime it for refilling.

   • While shaking the tin can, y'all'll also be able to feel fluid swish around inside information technology. This will requite you lot a chance to gauge how much is in the bottle.
   • Nearly empty bottles may not have enough fluid to fully refill your lighter and should be swapped out for a new can of replacement fuel.^[17]

6. 6

   Secure the tip of the refill bottle into the refill valve on the lighter. Make certain y'all are property the lighter and refill canteen directly up and downward. In some cases, the bottle tip may not form a secure fit with the lighter'southward valve. In this situation, use a tip adapter.

   • Well-nigh butane refill bottles come with an adapter, then before yous endeavour to refill, make sure the standard tip fits over the valve.
   • Don't fill the lighter at an angle. This will let air into the lighter tank. Air in the lighter will cause the lighter to non piece of work properly. It will take to be drained and refilled.^[18]

7. 7

   Fill the lighter for about five seconds. Pressing the lighter down onto the bottle will disengage the release valve on the bottle's nozzle. Press down on the lighter firmly for virtually five seconds to refill the lighter.^[19]

   • Later filling, if y'all feel like your lighter isn't full, repeat this procedure for another v seconds. Refill cans low on fuel may have more than time to refuel lighters.
   • Some lighters have a fuel level that yous can check. Cheque the butane level viewer if y'all take i to gauge the lighter's fullness.
   • Lighters that are filled up too much will overflow. This tin can be unsafe, equally butane can leak and take hold of fire when lighting.

8. eight

   Set the desired flame meridian. Flip your lighter over and reset the adjuster to its starting position. Ideally, the flame should be near ane to 1 ¹⁄₂ inches (2.5 to three.eight cm) tall. Before attempting to examination the lighter, allow the butane settle for a few minutes.

   • Once yous've refilled and prepare your flame height, requite your lighter a minute or so to absorb the butane.
   • As you wait for butane to be absorbed, check your lighter for leaks. Wipe up leaked fuel with a dampened rag. Rinse the rag frequently.
   • If your lighter leaks, you may accept to purge the fuel and refill it once more. Check for obvious culprits first, like loose fasteners, before purging and refilling.^[20]

9. 9

   Test the lighter. If at that place are any spills or if you odour even a hint of fumes, look a few more minutes for these to dissipate. Hold the lighter at a condom distance from your face and ignite the flame. You may need to add more butane if the flame does not catch or seems weak.

   • In most butane lighters, butane won't dissolve over time. Always test your lighter before refilling it to make sure that it is empty.

1. 1

   Utilise authentic Zippo Lighter Fluid. Other brands of lighter fluid intended for like lighters will work near of the time, only the Aught fluid is recommended by the manufacturer for maintaining its status and operation.^[21]

   • If y'all use a different brand of lighter fluid, make sure it is a premium make. Sub-par fuel may neglect to ignite in your lighter.
   • Never utilize charcoal lighter fluid. Charcoal lighter fluid is not fabricated for a small container like a Nothing. Using charcoal fluid tin exist very dangerous.

2. 2

   Remove the insert from the case. The insert, which includes the chimney-shaped current of air baby-sit, should be wedged inside a rectangular metallic case. Utilise your fingers to pull the insert free of the case.^[22]

   • Catch the chimney cap, the minor rectangular portion with holes in it, and pull the lighter out. In some cases, y'all may demand to loosen the insert by wiggling it back and forth.
   • The refill admission for Zippo lighter's (and most similarly designed lighters, also) is at the bottom of the insert.

3. iii

   Lift the felt pad. Flip the insert over so the bottom faces up. You'll see a small circular pin. Surrounding this pin and sealing off the bottom will be a rectangular slice of felt, known as the felt pad. Lift the felt pad at the designated location with a screwdriver.^[23]

   • The rectangular felt pad will say "LIFT TO Fill up" on it. Lift the felt pad from this terminate to reveal the rayon balls, which wait like cotton fiber, and a wick underneath.
   • There may also exist a pocket-sized hole in the centre of the felt pad. Utilise a pocket-sized screwdriver or pen and insert information technology into the hole. Utilise your tool as a lever to pull the felt pad up.

4. 4

   Squirt in lighter fluid to refuel the lighter. While property the felt pad back, put the tip of your lighter fluid into the lighter insert and squeeze gently. Keep squirting lighter fluid until you lot see the top portion of your rayon assurance dampen.^[24]

   • Be careful non to let lighter fluid drip down the outside of your Zippo or get any on your easily.
   • Wipe upwards spills with a wet rag. Rinse the rag regularly while doing and so to flush fuel down the drain.
   • Refill slowly so you don't overfill the lighter. If you lot add likewise much fluid, your lighter will leak, which can be unsafe.

5. 5

   Push the top felt pad dorsum downwards. Release your hold on the felt pad and wedge information technology back into identify with your fingers or tool. Let the fluid soak in for about 45 seconds before flipping information technology right side up. Wipe the outside of your lighter with a damp clean rag or paper towel.^[25]

   • It's also a skillful thought to launder your easily earlier placing your lighter back into the casing. Some fluid might've transferred to your hands without you noticing.

6. half dozen

   Insert your lighter back into the casing. But slide your Zippo back into the casing. Push down on the chimney to firmly wedge it back into place. Snap the lid shut to brand certain the insert is low enough.

7. vii

   Test your lighter. Light your Zippo to make sure that the wick is absorbing the fuel and your flint is creating a spark. If your lighter doesn't spark up, the well-nigh likely issue is the flint. Check out fixing and replacing this part in the next method.

   • The beginning couple of times you light your Nothing later refilling, your flame may be bigger than usual. This is completely normal.

1. 1

   Unstick stiff flint wheels. You lot shouldn't take to replace the flint of stuck flint wheels. Normal flints mechanisms accept three parts: a spring, a flintstone, and the flintstone wheel. When new, these parts can stick, preventing sparks needed to ignite the flame. To resolve this issue:

   • Open the lighter. Remove the insert from the lighter example by pulling on the insert by the flame baby-sit, which is the raised part of the insert with holes in it.
   • Remove the flat head slotted spiral fastening the flint spring at the bottom of the insert by turning information technology counterclockwise with a screwdriver.
   • Pull out the screw and attached flint jump. Tap the pinnacle of the lighter to knock the flintstone loose. Supercede the flintstone, leap, and refasten the screw. Your flint wheel should be unstuck.^[26]

2. ii

   Unfasten the flint screw at the bottom of the insert to replace the flint. Pull the lighter insert from its case. Turn the insert upside down. Yous should see the contumely spiral fastening the flint jump. Unfasten this with a screwdriver or the example of the lighter.

3. iii

   Remove the flint. While keeping the bottom of the insert oriented up, pull out the unfastened screw and attached flint jump. Tap the insert gently into your palm to knock loose the flint so it falls into your hand.

   • The flint will look similar a very modest cylinder roughly the size of the flint jump tip. Old flints tin can be thrown away.^[27]

4. 4

   Supersede the flint and reassemble the flint mechanism. While holding the insert so its lesser is all the same facing upwards, drop the new flint downward into the flintstone pigsty. Reinsert the bound into the hole and refasten the screw.^[28]

5. 5

   Test the new flintstone. Replace the insert back into the instance. Make sure the case is seated correctly by closing the case. When the insert is correctly positioned, light the lighter as you would normally.

   • If, after replacing the flintstone, your lighter yet doesn't work, information technology might exist out of fuel. Check and refill fuel as necessary.

Ask a Question

200 characters left

Include your e-mail address to get a message when this question is answered.

Submit

Video

• Ever refill your lighter in an open space with sufficient airflow.

• Recollect to purge the air from your butane lighter before refilling.

• Wipe down your lighters afterward filling to remove any spilled fluid.

Show More Tips

Things You'll Need

• Empty disposable lighter
• Push pin
• Butane
• Safety grommets (x3)
• Sturdy clippers (optional)
• Metal file (optional)

• Screwdrivers (x2; one small and 1 normal sized)
• Empty long-stemmed lighter
• New disposable lighter

• Screwdriver (modest size)
• Cover for piece of work surface (like newspaper or a drib cloth; optional)
• Butane
• Empty refillable butane lighter

• Empty Cypher lighter
• Zippo lighter fluid
• Flathead screwdriver

• Replacement flint
• Flat head screwdriver

Almost This Commodity

Article Summary Ten

To refill a disposable lighter, kickoff by turning it upside downwards and inserting a push pivot into the hole. Next, flip the lighter around then the pivot is resting on the work surface and push down on the lighter. Then, point the lighter abroad from you and remove the push pin. To add together the fuel, insert the tip of a butane applicator into the valve. Button down on the bottle to disengage the release valve and fill the lighter. Finally, remove the applicator and seal the valve quickly with the push pin. For tips on how to refill a nil lighter or a butane lighter, keep reading!

Did this summary assistance you?

Thanks to all authors for creating a page that has been read 694,133 times.

Did this article help you?

Source: https://www.wikihow.com/Refill-a-Lighter

Share this post